Portasol Gas Soldador de ... se ha añadido a la cesta

Enviar a:
Para ver las direcciones, por favor
O
Introduce un código postal válido.
O

¿Tienes uno para vender? Vender en Amazon

Portasol Gas Soldador de Juego

4,4 de un máximo de 5 estrellas
5 estrellas
154
4 estrellas
23
3 estrellas
12
2 estrellas
9
1 estrella
14
4,4 de un máximo de 5 estrellas 212 opiniones de EE. UU.

Precio: EUR 137,48 Envío GRATIS. Ver detalles
Precio final del producto
En stock.
Vendido por Alida Systems ® y gestionado por Amazon. Se puede envolver para regalo.
  • Funciona con butano - sin cables ni alambres.
  • Con tanque de gas soldado mediante ultrasonidos para ofrecer mejor resistencia, seguridad y fiabilidad.
  • Alta potencia ajustable de 25-130 W (equivalente).
  • Fabricado en Irlanda.
  • Listo para derretir la soldadura menos de 30 segundos después del encendido.

Especificaciones para este producto
CUP 705554409902 , 782386201690 , 857391002027 , 753956377947 , 756635834083 , 031111202502 , 642008199951 , 782386211040 , 857391002034
EAN 5099681400020 , 0756635834083 , 0642008199951 , 0031111202502 , 0782386201690 , 0753956377947 , 7535001816969 , 7241870760097 , 0857391002034 , 0782386211040 , 0705554409902 , 0857391002027
Nombre de la marca PORTASOL
Número de parte 010589330
Número de productos 1
Peso 88 Centésimas de libra


Detalles del producto

  • Dimensiones del producto: 21,5 x 2,6 x 2,6 cm ; 399 g
  • Número de modelo del producto: 10589330
  • ASIN: B003H6NN2Q
  • Producto en Amazon.es desde: 23 de septiembre de 2013
  • Valoración media de los clientes: Sé el primero en opinar sobre este producto
  • Clasificación en los más vendidos de Amazon: nº1.916 en Industria, empresas y ciencia (Ver el Top 100 en Industria, empresas y ciencia)
  • ¿Quieres informarnos sobre un precio más bajo?

Descripción del producto

Kit soldador Superpro 25-125W 580°C - Portasol.Ref: gas/proset - Características encendido piezo eléctrico regulación de potencia 6 modelos de puntas depósito a gas de acero inoxidable para una autonomía de 2 horas figura: 1): punta 2): catalizador 3): tubo para la protección de la punta 4): tuerca de fijación (para fijar el elemento calentador) 5): caja de acero Especificaciones autonomía: 120 min. recarga: 30 seg. temperatura máx. de la punta: 580°C temperatura ajustable equivalente a los soldadores de 25 - 125W punta estándar (incl.): BITSP2.4, BITSP4.8, BITSP/B, BITSP/K, DFLECTOR puntas disponibles: BITSP1SF, BITSP2SF, BITSP3SF, BITSP4SF, BITSP1.0, BITSP2.4, BITSP3.2, BITSP4.8, BITSP/B, BITSP/K, DFLECTOR


Preguntas y respuestas de los clientes

Opiniones de clientes

Todavía no hay opiniones de clientes en Amazon.es
5 estrellas
4 estrellas
3 estrellas
2 estrellas
1 estrella

Opiniones de clientes más útiles en Amazon.com (beta) (Puede incluir opiniones del Programa de Recompensas de Opiniones Iniciales)

Amazon.com: 4.4 de un máximo de 5 estrellas 212 opiniones
15 de 15 personas piensan que la opinión es útil
5.0 de un máximo de 5 estrellas The best butane iron kit for the money and the same as weller model 15 de mayo de 2012
Por Johnny 7th Avenue - Publicado en Amazon.com
Compra verificada
Just a few comments about the Portasol Super Pro 125 iron, it is a different color than its brother the Weller which I like better with balck and chrome as opposed to grey and orange but the tips and everthing else are the same. I've owned the Weller for about 6 years and wanted to get more tips. When I added up the cost of the tips it made economical sense getting this set with ALL the tips and a new iron. This iron (as well as the Weller) gets super hot super fast, ignites with a click or 2 and runs for well over an hour continuous. I do turn the gas down to low while I position the next wire etc. It also gets hot enough to loosen up smaller frozen bolts etc. using the included flame tip. This kit cannot be beat it literally has every tip and tip size you will ever need all in a nice case too. I wish I would have bought this kit to begin with just because of the price and value. The older Weller I have still works perfectly and I will leave it at home as a spare since I work in the field on the road. I do carry an electric iron just in case I run out of butane but that has not happened to me. Plus the butane is available almost anywhere. An electric iron still may be necessary if you are workin in a very small, tight place where other objects are to close because of the exhaust port so keep that in mind, read below!
As mentioned in other reviews the built in stand (the Weller model too) is pretty flimsy but works and but mine never broke. The cover can be used to rest the iron on too and what is also neat is when the cover is on correctly it insures the gas is off and stays off.

Notes of caution- the tips have an exhaust hole so be VERY CAREFULL which direction the exhaust is blowing, the exhaust air is super hot it will burn wood, melt plastic, insulation or burn just about anything in it's path!! Beleive me, I found out the hard way when I first got it, used it and placed it on a very expensive table top while it was still on and the port was facing towards the table...as I said I learned the hard way. The instructions do mention that but it is something you MUST remember and plan ahead !!
So if your in the market for performance and value in a portable butane iron this is the kit to get but remember BE CAREFULL !!!
3 de 3 personas piensan que la opinión es útil
4.0 de un máximo de 5 estrellas Nice multi-purpose soldering iron, but tip wears out quickly 8 de diciembre de 2016
Por Dennis Lee - Publicado en Amazon.com
Compra verificada
Very nice product:
Easy to refill, just push the nozzle of a butane canister against the filling port. Fills in about 30 seconds. Can be emptied by using a pin to push against the filling port, so you can carry it on board planes(that's what a ground crew told me, never tried that though)

It is also easy to light up, by just turning on the gas switch and clicking the piezo once. For the tips with in-built catalyst (all tips except the open flame tip), it is even possible to relight it without clicking the piezo, after the gas is switched for a short while and turned back on.

It comes with a hot air blower+deflector tip inside the box. Not sure why I had an extra hot air blower tip though, but it's good to have a spare.
The deflector, once attached to the hot air blower, is quite hard to remove and requires a lot of force to pull off. So when using it I never slide it down to the bottom of the hot air blower nozzle.
The blower is good for heat shrink tubes. I have also used it to remove a BGA chip on the lowest temperature setting. But the airflow isn't that constant, as it sometimes audibly spews out a gust of hot air. I guess it might be because of the clogs from using cheap butane gas. Also, I can still start the fire properly on the lowest setting, unlike experiences of some other customers.

The soldering tips come pre-tinned, but for me it wears out pretty fast. The 1mm double flat tip that came with the kit wore out pretty fast even with infrequent usage. It wore out after about a year of usage. Not sure if it is a problem with the rosin in the solder I'm using or problem with the tip. It just became impossible to tin and various parts of the tip became black. When that happens I just used a fine grit sandpaper to sand a bit of it down and it becomes usable for a while. But after a few cycles the tip developed a well/a dip at the center and becomes very thick.
Thereafter I bought a 1mm single flat tip from amazon, this time using a goot brand tip tinner (well it might be acidic). However after half a year of infrequent usage the tip become like the abovementioned one, developed a dip in the tip of the tip. The thicker tips are pretty useless for me, to be honest. They also became very hard to tin after a short period of usage.
Can someone tell me why is it happening? One guess is that the high heat is decomposing the rosin and causing it to stick on the tip?

The blowtorch/open flame tip is also a nice addition. I often use it to light barbecue fires.

I haven't found much of a use for the hot knife tip. Only used it once to cut out a circle from an all-in-one's scanner cover(for a science project). I have to set it on the highest temperature settings in order to cut through the plastic.

The cap is good to prevent the iron from melting objects around it after use. It is cool enough (though still quite hot) to hold by hand even if you directly cap it after use. The iron comes with a built-in kickstand, but sometimes it is an annoyance as there seems to be no clip that hold it in place. When the iron is held with the wire kickstand down, it will just dangle. Also seems like the kickstand is anchored near the center of gravity of the iron, so it acts like a seesaw sometimes: both the tip side and the nozzle side can be made to touch the tabletop easily, which defeats the purpose of preventing it from burning the table. So I just use the cap instead.

The sponge is very small so it isn't very useful. I just bought a brass/copper wool tip cleaner from ifixit. It is something similar to the hakko clamshell one. That cleans up the tip much better than the sponge. I remember seeing someone who said that only a piece of yellow paper came in the tray, but if you add water to the "yellow paper" it will magically turn into a sponge :P.

Overall a good product to have, but may be a bit overpriced if you don't use it so often. (but the build quality justifies the price :P) Already owned it for over 4 years.

Just realized the order for this was placed on this account in 2012 XD. I'll get the verified purchase tag on this one.
5 de 5 personas piensan que la opinión es útil
1.0 de un máximo de 5 estrellas Its a toss up if you get a return or a new one!!!!!!!!!!!!!! 26 de febrero de 2015
Por Shay - Publicado en Amazon.com
Compra verificada
It worked well for me 3 times. Then it wouldn't light by its self or with anything else. So I changed out the metal in the tip I was using and it worked again but it only worked 1 time. I starter looking at all the other tips and the metal in the rest of them have been used up. Its like it was returned to them and they gave me a return. You would think for the money i spent on this I would of got a new one and I would be able to use it more then 4 times. So now good luck on yours. I guess its a toss of the dice if you get a new one or some ones return.
3.0 de un máximo de 5 estrellas Great when it worked 13 de diciembre de 2016
Por Swammazon - Publicado en Amazon.com
Compra verificada
Seems like most people have had great results with this torch. It performed well in the beggining when it worked. But then I started to have to start it with two to three clicks before I got it to light up. I thought maybe it was me, since I though this was like the SnapOn of portable Butane lighters, but lo and behold it started to degrade to the point that it took 5-10 and 10-20 clicks to get it to start. People at the shop were looking at me like I was retarded. Mind you I made sure it was full of Butane and that I used high quality Colibri Butane. I eventually went for the Power Probe Lighter, stay tuned for that review!!
2.0 de un máximo de 5 estrellas Nice Start, But Disappointingly Short Lived after Waranty Expired 29 de junio de 2015
Por mbon - Publicado en Amazon.com
Compra verificada
This product failed at 2 years from purchase. I had hoped that the stated and reviewed high quality would last significantly longer especially given my occasional use (avg. 1 or 2 hrs at low temp every 2 weeks). My only complaint was that upon refill, lowest setting always too hot, moderating as tank depleated. Tips always kept clean and tool stored carefully in box. Noted that the main extended shaft (inseparable from body) differes from diagram on multi-lingual fold out instructions, but assume reflects a revision to product or printed guide rather rather than defect since other than noted tool was reliable and very useful prior to "no light" failure. Honestly not worth premium price for product that dies after 2 years. The cheap Weller butane irons cost $20 and last as long.